whomever built it had no idea that they should stagger the deck boards. the deck was built in 2 parts at 2 seperate points in time. as long as the deck is solidly built and is not actually 2 separate decks stuck together, i'd definitely stagger the decking and not install the decking in the same arrangement.
staggering deck board patterns. you should consider staggering the joints and i would cut some of the deck boards into 6' lengths. you should start one row with a 6' and 12' arrangement. the next row do a 12' and 6' arrangement. you would run these along the 18' side. this will look better and may even be stronger.
the deck is more structurally sound if you stagger. if you don't, the center beam/joist should be doubled up. you're essentially building two 8x8 decks next to each other with the center beam carrying double the load it should be, if not doubled up. if you stagger them, that is not the case.
bob and carpenter bob ryley continue working on the backyard deck. once they've finished theframing, they begin laying the deck boards.
with a staggered deck, each successive row is offset from the rows adjacent to it by one half of a board so that there are no long, uninterrupted vertical seems. step 1 lay your first board, starting in the corner of the deck, perpendicular to the support beams of your frame, along one edge of the deck.
how to stagger deck boards. wooden decks are a common exterior addition to homes, allowing families extra space to use when enjoying the outdoors. decks feature planks for walking on, but if these boards are shorter than the decks width, more than one plank has to be used per row. patterns from staggered joints are a way
hometime how to, decks - installing deck boards. installing deck boards usually begins at the house wall and goes out toward as the deck boards progress, it's a good idea to measure out to the front of stagger the joints between the courses of decking for a more pleasing appearance.
usually it is easiest to place the deck boards flush with the outside edge of one of the outer joists and let them 'run wild' at the other end. this way, all of the uneven ends can be cut all at once. the only other trick to applying the decking is to drill pilot holes when nailing near the end of a board.
difficulty: moderate. you may have seen a chevron deck pattern before, but adding transition boards opens a world of possibilities. the transition boards make the pattern options endless while still allowing you to use shorts. carry a chevron pattern across the whole deck, or use strht boards in some sections.
give it a dry run and stagger the boards. do a dry run of your boards by laying them out before attaching to the frame. if your deck dimensions are longer than your decking boards, staggering the joints is important when laying decking boards. the staggered boards improve stability and the appearance of the deck.
why do builders stagger deck boards. top 10 deck-building mistakes - fine homebuilding mar 19, 2012 the process of building decks is not nearly the same today as it was a directions to deck builders to bolt deck beams to the sides of support posts. overspanning composite decking is most commonly a problem when deck boards are .
how to stagger deck boards home guides sf gate. wood swells when it is wet, and it will also expand in warmer weather. deck boards are best installed when dry, and you should include at least a 1/8-inch gap.
has any one ever staggered the deck boards to have an interior floor look or am i sucking wind. thanks warning: the topics covered on this site include activities in which there exists the potential for serious injury or death .
on each side of the deck, measure out from the house the width of a decking board plus an additional ¼ inch. mark the location on each end joist. snap a chalk line between the two marks. use the strhtest board you can find for this first row, and install it so the outer edge is aligned with the chalk line.
i'm looking for some tips on how to join decking boards end on. the deck is approximately 3.3m by 9m and built using 4.8m pressure treated boards. we decided it would look better with the boards running parallel to the 9m length so will need to butt join the ends somehow.