i attach the plastic with black duct tape and secure it with staples through the plastic and tape. it holds great until i'm ready to take it down. kristi is right - make sure the plastic is tight - that's where the duct tape comes in handy. also, the tape won't tear when you staple through it.
the following bostik and alcolin products are recommended for sticking wood to plastic: waterproof glue, pu sealant and adhesive, build, woodmate, fix-all, gripfill, rapid epoxy, super glue, blits stik super glue, soft plastics
how to fasten anything to concrete. but attaching to concrete really isnt much more difficult than fastening to woodif you use the correct tools and specialized fasteners. these four
how to attach plexiglass to wood by alexander callos while it may seem like a quick and easy task, attaching plexiglass to wood involves a few detailed steps that must be followed to keep the plexiglass from chipping and falling apart. care should be taken in attaching plexiglass to wood. step 1
fasteners include nails and screws that are used to affix the sheet metal to the piece of wood. drilling holes through a thin sheet of sheet metal, such as that used for a roofs flashing, does not require a lot of effort and will make attaching the sheet metal easier.
joining techniques engineering plastics. mechanical fastening 5 screws, bolts and rivets 6 molded-in threads 7 self-threading or self-tapping screws 7 thread-cutting 7 thread-forming 8 screw bosses large plastic panels to metal or wood frames to account for the differing
these self-tapping screws are easy to use because they don't require pre-drilled holes. i used them to fasten polycarbonate panels to a wood frame. the washer seals the hole when the screw is tight. the screws performed the function they were designed for very well.
related articles. use 3/8-inch staples to fasten the plastic to the length of the horizontal wood framing every 6 inches, stretching it taut along the way. staple it in the same fashion along the wood posts at either end of the frame, as well as the horizontal base board at the bottom of the frame.
plastic moldings and trim can be molded into intricate shapes and bent to fit curves that would be impossible with wood. they can be designed to resemble any material, including the grain of wood. plastic molding and trim are impervious to moisture, making them resistant to termites, rot, mold, warping, cracking, and splintering.
attaching plastic castings to wood mary 8 years ago. if you make plaster wall ornaments it is better to cast wall plugs into the wet plaster ornament. you can then screw wood into the dry plaster ornament. then screw the wood into the wall. so this method will work for new castings. or cast wire into the back of your wet plaster casting.
choose from our selection of wood fasteners, including tapping inserts for wood, hammer-in tee nut inserts for wood, and more. in stock and ready to ship.
most adhesives don't adhere to plastic. in addition to using a construction adhesive i think i would drill and countersink the lego plates and put some screws in them. to make it look nicer you could paint the heads of the screws the color of the lego.
two-part epoxy. epoxy is an especially useful adhesive for the bonding of smaller plastic pieces to wood, glass, metal and other materials used in crafting and other applications. mix equal parts resin and hardener together in small quantities according to the manufacturer's instructions. dries hard, almost glassy.
to adhere plastic to wood, use super glue or hot glue for small projects or epoxy or contact cement for bigger jobs. for super glue, you'll need a heavier-duty adhesive like loctite or gorilla glue, which will have a stronger hold than regular super glue.
hold your wood or other material in position and drill through it into the concrete to the correct depth. slip in the anchor photo 3 . to finish the job, strike the exposed pin with the hammer and drive it in. dbacks: once you anchor hammer-set fasteners, theres no easy way to remove them without destroying the material or the fastener.
flat head screws for wood more corrosion resistant than 18-8 stainless steel screws, these have excellent resistance to chemicals and salt water. brass phillips flat