building peaked roof on mobile home. repair help for the do-it-yourselfer. i would like to build a peaked roof over top of the metal roof on our mobile home 52x14 i think . the extra weight if yore home is 2x4 const and you have a double top plate youl be ok if it is a single plate simply add another one to help carry the load. now
at stores like mobile home parts store, you can buy carport kits that they will attach to your home. convert to real es. technically, this might not be an addition. but it is something that can add a lot of value to your mobile home. converting a manufactured home to real estate will increase its value and make it easier and more attractive to finance.
mobile home roof over materials there are a variety of options available that can give your roof the protection and look you desire without the need to remove your existing roof. mobile home roof overs for flat roofs typically involve metal or rubber or pto.
metal roof overs can be installed over most mobile home roofs . keep in mind, however, that the insulating layer of a metal roof does increase the thickness of the roof by several inches, which in turn, will increase the height of your mobile home.
in this video we go over how we put a metal roof over shingles on our mobile home. this was completely completed by me from the beginning to the end over the course of about 2.5 months on the few
the hud code more on this later has very strict requirements on how to attach the roof of an addition to your mobile home. you might also require additional or more stringent permits. did someone say sunroom? if you are planning on building a porch with a roof, you might consider going all the way and creating a sunroom or screen enclosure.
step 6: attach the roof shingles and vent. the shingles should have a lip or attachment that will allow you to nail them down on a nailer strip that you installed over the tar paper. work carefully to attach the entire row before moving on to the next. with the foam roof shingles in place, attach the vent and other elements of the roof to complete this project.
depending upon the current pitch, this could be a fairly involved project. there are, however, metal roofs designed for low slope mobile home retrofits. i would encourage you to look for a contractor in your area who specializes in mobile home repair.
roof, and over the furring strips, to mark the location of the rafters. use a drill and 3 ½ inch deck screws to secure the furring strips to the rafters. 3 use a tape measure to measure the width of the roof and add an additional 8 inches for overhang allowance. use a circular saw to cut the corrugated sheets of metal to the correct size.
sealing the addition roof to the mobile home roof. to connect the additions roof to the home if the addition is lower than the roof on your home, you will need to use flashing to seal the gap between the home and the addition.
how to install metal roof on a mobile home installing a metal roof on a mobile home can be a do-it-yourself project saving you a lot of money. the most difficult part of the project is removing the old roof and scraping the roof clean of debris.
fasten the porch roof to the house with a horizontal lumber ledger board, bolted to the house wall studs at the top and rear of the roof. install a beam on top of the posts along the front edge of the porch. slant the rafters down from the ledger board to this beam and attach the ends with hanger brackets.
to stop leaks or water damage. to change the look of a home by turning a flat roof into a pitched one. improve energy efficiency in winter and summer. extra stability and fortitude to your roof. depending on the type of roof over your roof might also make less noise.
if your mobile home will stay in place for a long time, consider attaching the porch roof to the mobile home structure. talk with mobile home dealers about how your mobile home was manufactured. follow their suggestions about attaching the porch to wood or metal beams.
joining porch roof to mobile home. which is to say that the porch roof would not be a free-standing structure--no inner row of posts up by the house. the house is anchored to the property per fha requirements and is certified as such, and the porch is anchored by two rows of concrete pilings set 2' into the ground,
someone we used to know in rural idaho made his roomier by essentially building a frame and roof around and beyond the dimensions of the mobile home. he sided the whole thing, thus sort of encapsulating the mobile home. then he made openings from the mobile into the added area. it actually turned out pretty well.