how to replace fence post anchors in concrete, or fence post spikes without concrete. if you have an old wood fence post that is completely rotted off and you are able to remove it along with all debris, you could reuse the cement ball for a new post. some have successfully used fence post anchors. this way the post will not be sitting in cement to rot off again.
benefits of post buddy fence repair. the easy yet effective diy solution for repairing broken wooden fence posts tried and tested over 200,000 post buddy stakes sold so far saves hours of hard work - no need to dig up the post or take the fence apart
how to replace a rotted fence post. if possible, completely remove the fence panel at either side of the post. support the panels from below with blocks concrete blocks, bricks, stacks of lumber, etc. to keep them level, then remove the fasteners securing the panels to the posts. if the joints have nails that are hard to get out,
replacing a post. separate the fence from the post to be replaced, then dig up the old post removing it and the old concrete footing. place the new fence post in the existing hole and pour a new concrete footing. keep in mind, it is always a good idea to temporarily brace the new post to keep it level and plumb while the new footing cures.
how to replace a fence post in concrete - placing a new post coat the bottom of wood posts with copper naphthenate. fill the bottom of the hole with aggregate. place your post inside the hole. check the posts vertical orientation with a bubble level. fill the hole with concrete. slope the
replacing or repairing rotting deck support posts. the supports are sitting on top of concrete a foot down i think. i got two estimates to fix it 1 jack deck up and replace 6x6's and put rubber sleeve on them. 2 summary: concrete three 6x6 support posts under deck, concrete above ground and a 10 ' diameter around existing 6x6 posts.
how to replace a rotted fence post 1. mark cut lines onto post with a layout square. 2. set the depth of cut on a circular saw to cut through the posts, but not into the rails. 3. knock out the wood between the cuts with a hammer. 4. use a cordless drill to remove any screws securing the post to
concrete footings can crack or heave, and a tamped earth-and-gravel footing can soften over time. a failed concrete footing is hard to repair, and the best solution is to replace the fence post
up vote 4 down vote favorite. i need to replace a wooden fence post that was set into concrete. the post has snapped through rot at the base and the rot has set in so far that the post snapped about 2 inches beneath the surface.
there are temporary fixes available but often the best option is to replace the post. even if a fence post is not rotten above ground, older posts may be rotten below ground. this happens mostly in the region just below the surface where the wood is both damp and exposed to the air. to replace a timber post in the same position as before is not easy. first of all you must remove the concrete. not only is this a heavy job in itself, but it will leave a large hole. that makes using concrete
the home mender, dustin luby, shows us how to remove and replace a 4x4 fence post. click the links below to see inside 'dustin's toolbox'. you can do it home mender. 6' pry bar for posts https
unfortunately, when such a fence post is broken off at ground level, removing the concrete or cement base by bolting a strong piece of wood to the fence post and using it as leverage isn't
solution: set the new fence post so it wont rot figure a: fence post footing when setting a fence post, you should always pour concrete so it extends a few inches above the grass and taper the edges to drain water away from the wood post.
also if you have a wood fence post try out fence post mender to repair that cracked or rotted fence post timber in minutes without having to remove any concrete. fences posts are usually pretty cheap to replace but the labor involved can ruin your plans for the rest of the day.
removing an old fence post can be a pain in the ass especially if the post has rotted and fallen off. thats because fence posts are set in a concrete footing that is usually at least two feet deep in the ground.
the challenge in replacing an existing fence post is the block of concrete that is left in the ground. either the block needs to be removed or a new post hole dug adjacent to it. in this case, the old post was pulled out of the concrete leaving a 12 hole very convenient
yank the fence post out of the ground after youve broken off enough concrete to lighten the load. if you have a rotting fence post that needs replacement, heres how to get the concrete pier out of the ground. its not complicated, but youll definitely work up a sweat. first, dig a