re: installing ledger board over stucco if you gapped the ledger with washers to allow water pass through it would be okay as long as your solid. if your not sure then tack the ledger to the house with nails then use the board as a guide for a grinder with a diamond blade to score the stucco. clear out the area.
a ledger, also known as a rim joist, provides an anchoring point for floor joists that span from one side of a cinder block wall to a stud-built wall or another cinder block wall.
tim carter, of askthebuilder.com, demonstrates a really simple way to nail wood to a concrete floor. sign up now for tim's free weekly newsletter at:
attach the ledger board. use lag bolts to the homes sill plate or framing based on your plans. install waterproofing and flashing. attach a self-adhering waterproofing membrane to the wall and over the top of the ledger board. attach all necessary flashing over the top of the membrane. dont be afraid to go overboard.
but also transfer the markings on the house wrap for the bottom of the ledger board, rim joist height and top of deck boards to the flashing. use masking tape. a story board is a strip of wood placed against a wall with predefined measurements and commonly used when installing siding to keep the boards parallel.
attaching a deck to brick house foundation. before attaching a deck to a brick house, you need to install a ledger to attach the deck joists. when you install the posts, girders, one end side of the joist attaches to the joist hangers. the outer sides will attach to the top of the girders and form a decks frame.
post base attachment. hold your drill plumb. use a drill with a hammer drill bit to install a concrete sleeve anchor into the center of the concrete footing. don't over tighten the bolt. install the adjustable post base to the sleeve anchor and tighten the bolt to secure the attachment. place your foot behind the post when nailing.
in summary - attaching a ledger to brick. it is important to the success of any project to resolve any questions before you begin - as mr s has wisely done by requesting information on attaching a ledger to brick. careful planning means a much more enjoyable build and often less wastage in time and in materials.
how to attach a ledger board to a vinyl sided house. the ledger board is a horizontal framing member, usually two-by-10 or two-by-12 lumber, that supports one side of a deck and attaches flat to the wall of a house after removing a section of siding. deck joists are typically attached to the face of the ledger board with joist hangers after
spread footing. the primary purpose of the footer is to spread out the weight of the structure across a larger footprint than the foundation would if it was in direct contact with the earth. frequently a concrete footer is 20, 24 or even 30 inches wide and at least 8-inches thick. more often than not youll see them 10-inches thick.
you probably know that attaching wood to masonry isn't as easy as picking up a hammer and a nail, but it's also not an impossible task. it's something that you can do yourself with the proper tools. if you're looking to add a shelf to your concrete mantle or maybe you have a brick wall in your home and want to hang some pictures, there are a few things you need to know.
next, attach the post caps with nails. set a beam on the caps crown side up and secure it to the bracket. if your beams are constructed of boards laid end-to-end, make sure the joints are over brackets.
attaching a wood table top without allowing for movement due to seasonal changes can cause the wood to crack over time. the best way to attach a table top is with table top fasteners. the fasteners allow the top to move throughout the seasons, help to prevent cracking and ensure your diy table top will be beautiful for years to come.
introduction. no clamps no problem this tutorial demonstrates attaching the top panel using thickened epoxy since the inside of this board is sealed. if you are building a board without sealing the inside, you can use titebond 3 on the feathered edge and pl seven trust or 3m 5200 on the ribs.
attaching a sill plate to a cinder block foundation requires the use of anchor bolts embedded in wet concrete at regular intervals. local codes determine the size of the anchor bolts and the
under edit signature, compose your signature.you can change fonts, font colors, and sizes, as well as text alignment. if you want to create a more robust signature with bullets, tables, or borders, use word to format your text, then copy and paste the signature into the edit signature box.you can also use one of our pre-designed templates for your signature.